| 詳細參數 | |||
|---|---|---|---|
| 品牌 | YOKOGAWA | 型號 | PSCCM22AAN |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 硬PLC | 功能 | 模塊 |
| 工作電壓 | 電源組24VDC | 產品認證 | UL |
| 環境溫度 | 0°Cto,60°C | 環境濕度 | 5至95%,非冷凝 |
| 加工定制 | 否 | 產地 | 日本 |
YOKOGAWA PSCCM22AAN 16418-5312
PSCCM22AAN 16418-5312設置警戒時鐘wdt：機械設備的動作時間一般是不變的，可以以這些時間為參考，當plc發出控制信號，相應的執行機械動作，同時啟動一個定時器，定時器的設定值比正常情況下機械設備的動作時間長20%，若時間到，plc還沒有收到執行機構動作結束信號，則啟動報警。
PSCCM22AAN 16418-5312提高輸入信號的可靠性：由于電磁干擾、噪聲、模擬信號誤差等因素的影響，會引起輸入信號的錯誤，引起程序判斷失誤，造成事故，例如按紐的抖動、繼電器觸點的瞬間跳動都會引起系統誤動作，可以采用軟件延時去抖。對于模擬信號誤差的影響可采取對模擬信號連續采樣三次，PSCCM22AAN 16418-5312采樣間隔根據a/d轉換時間和該信號的變化頻率而定，三個數據先后存放在不同的數據寄存器中，經比較后取中間值或平均值作為當前輸入值。
優勢品牌：
英維思?？怂共_
施耐德
英維思 Triconex
ABB
西屋
伍德沃德
本特利·內維達
通用電氣發那科
霍尼韋爾
橫河
艾倫-布拉德利
西門子
博世力士樂
XYCOM
摩托羅拉
喜馬
Psccm22aan 16418-5312 ? set the alarm clock WDT: the b time of mechanical equipment is generally unchanged, which can be used as a reference. When PLC sends a control signal, execute the mechanical b accordingly, and start a timer at the same time. The set value of the timer is 20% longer than the b time of mechanical equipment under normal conditions. If the time is up, If the PLC has not received the b end signal of the actuator, it will start the alarm.
Psccm22aan 16418-5312 improve the reliability of the b signal: due to the influence of electromagnetic interference, noise, analog signal error and other factors, it will cause the error of the b signal, cause the error of program judgment, and cause accidents. For example, the jitter of the button and the instantaneous jump of the relay contact will cause the system misoperation. The software delay can be used to remove the jitter. For the influence of analog signal error, the analog signal can be sampled three times continuously. The sampling interval of psccm22aan 16418-5312 is determined according to the A / D conversion time and the change frequency of the signal. The three data are successively stored in different data registers. After comparison, the intermediate value or average value is taken as the current b value.
