| 詳細參數 | |||
|---|---|---|---|
| 品牌 | PROSOFT | 型號 | MVI46-MBP |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 硬PLC | 功能 | 網絡接口模塊 |
| 工作電壓 | 5VDC,5% | 輸出頻率 | 1100mA,最大值 |
| 處理速度 | 10Mbit/s,200Datasets/s | 產品認證 | UL |
| 環境溫度 | -40°C至85°C | 環境濕度 | 5%至95%（無冷凝） |
| 加工定制 | 否 | 產地 | 美國 |
在橋接模式下，MVI46-MBP將DF1 PCCC消息重定向到Logix控制器位于預配置的路徑。因此，在此模式下，模塊將依賴Logix控制器將DF1請求映射到預配置的Logix標記。橋接器映射配置是一個兩步過程。
首先，MVI46-MBP必須配置為將特定DF1地址路由到控制器路徑。
第二步是使用RSLogix 5000將DF1地址映射到Logix標記。DF1消息啟動器（如DCS網關）將向RS232上的特定DF1地址。您必須配置MVI46-MBP以路由發送給Logix控制器的特定DF1地址的消息。這將允許正確的Logix控制器將請求映射到Logix PLC/SLC映射標記。對于對于每個路線圖，必須輸入下表中所述的兩個參數。
網橋路由映射設置的第二部分是映射接收到的DF1請求由Logix控制器發送到Logix標記。這必須在羅克韋爾自動化公司完成RSLogix 5000。有關更多信息，請參閱本文檔中的附加信息部分有關Logix控制器中PLC/SLC消息映射的信息。打開通過從中選擇映射PLC/SLC消息，在RSLogix 5000中創建映射表菜單欄中的邏輯菜單項。您必須輸入請求的文件號和Logix標記名對，以確保讀或?qū)懻?qǐng)求路由到正確的Logix標簽。下面是RSLogix 5000 PLC5/SLC映射的示例。
In bridge mode, mvi46-mbp redirects DF1 PCCC messages to the pre configured path where the Logix controller is located. Therefore, in this mode, the module will rely on the Logix controller to map DF1 requests to preconfigured Logix tags. Bridge mapping configuration is a two-step process.
First, the mvi46-mbp must be configured to route a specific DF1 address to the controller path.
The second step is to map the DF1 address to the Logix tag using rslogix 5000. DF1 message initiators (such as DCS gateway) will send messages to a specific DF1 address on RS232. You must configure mvi46-mbp to route messages to a specific DF1 address of the Logix controller. This will allow the correct Logix controller to map requests to Logix PLC / SLC mapping tags. For each roadmap, you must enter the two beters described in the table below.
The second part of the bridge routing mapping setting is to map the received DF1 request sent by the Logix controller to the Logix tag. This must be done at Rockwell Automation rslogix 5000. For more inbation, see the additional inbation section in this document for inbation about PLC / SLC message mapping in Logix controllers. Open the logical menu item in the menu bar of the mapping table created in rslogix 5000 by selecting the mapping PLC / SLC message from it. You must enter the requested file number and Logix tagName pair to ensure that read or write requests are routed to the correct Logix tag. The following is an example of rslogix 5000 PLC5 / SLC mapping.
NI SCXI-1302
NI SCXI-1180
A-B 2711-K5A2/B
NI PXIE-6556
EMERSON 1C31116G02
BENTLY 125680-01
GE SR469-P5-HI-A20-T
